Each roof is novel and requires a trusted, professional roofing contractor Fort Worth, TX to completely inspect and give an estimate that is specific to your roof’s needs.
While you should increase the size of your roof by an estimated number for the cost of roofing materials and work, this is an oversimplified computation that leaves out numerous basic factors that can impact the complete cost of your roofing project.
Roof Size
The size of your home’s roof straightforwardly impacts its replacement cost. The more surface region you must cover, the more materials you will require, including OSB/pressed wood, underlayment, and shingles.
Roof Square Footage
The square footage of your house is not the same as the square footage of your roof, even though you can use that figure as a starting point.
Your home’s square footage, regularly listed during a sale or appraisal, is a sum of all gross residing areas. It includes each level of a house with different stories, however, it usually doesn’t account for garage space, basements, and inside walls.
You can find out how enormous your roof is in square feet by duplicating the length (in feet) by width (in feet) of every single level plane and adding them together. All measurements should race to the edge of each surface so that they incorporate any areas that extend out past the side of the house (like eaves or overhangs).

Roof Slope
Recollect figuring out how to ascertain rise over run in middle school math class? Roof slope is a genuine opportunity to do a rise over run computation to sort out the grade, or slope, of your roof.
Residential roofs might have steep slopes, low slopes, or a blend of both. Roof slope is expressed either as a proportion or fraction demonstrating the number of inches the roof rises upward for every 12 inches it runs on a level plane (rise/run).
For instance, a roof with a 10/12 (or 10:12) slope is a lot steeper than a roof with a 4/12 (or 4:12) slope.
As a general rule, the steeper the roof, the more expensive the project cost, and this is common because of safety reasons. For instance, an extremely steep roof could require special gear for the roofers to use while they work on it.
Roof Slope Factor
The slope factor of the roof also contributes to the all-out square footage. You can decide the slope factor with the guide of a mini-computer, however, roofing contractors ordinarily have slope factor charts that simplify the process.
On the off chance that you know your roof’s slope, you can find the slope factor using a table or online number cruncher. If you’re measuring the roof square footage starting from the earliest stage, the pitch factor needs to be added.
Waste Factor
Roofing contractors regularly add somewhere between 10-15% to the all-out roof square footage to account for waste factor, however, this computation can differ based on roof style or roofing materials. In roofing, the waste factor accounts for material that is covered in valleys and hips, as well as removed material around flashings, penetrations, and peak ends.
Roofing Squares
At some point when you work with roofing contractors, you might hear the expression “squares” being discussed as a component of roofing material estimates.
Roof surfaces are measured in squares. A roofing square is a region of your roof that equals 100 square feet and covers a 10′ x 10′ region. The quantity of roofing squares required for a project is determined by partitioning the complete roof region by 100 (which is 1 square).
For instance, if your roof covers a 2200 square-foot region, partition 2200/100 = 22, so your project would require 22 squares of shingles to cover your roof.
Roofing Materials
The kind of roofing shingles and materials you choose, or may try and be expected to have installed based on your geological area and neighborhood construction standards or HOA rules, will also impact the cost of getting another roof. For instance, conventional three-tab shingles may not cost the same as building shingles that also meet COOL roof code requirements.
Notwithstanding shingles, you may also have to replace or install new:
Decking
Underlayment
Vents
Flashing, around chimney stacks, skylights, or roof-to-wall transitions, for instance
Products inside these categories change in cost because of their differences in materials, performance, warranties, design or look, and different factors. For instance, a roll of synthetic underlayment commonly costs more than felt because it is a better item and covers more region than a roll of felt.
Roofing Design and Shape
The building style or design of a roof will also impact the cost of re-roofing. For instance, your roof could have a steep A-outline, numerous dormers, or a mix of gables and valleys.
A roofing contractor will probably consider the building design while giving a roof replacement cost estimate, and you could hear them allude to your roof as “cut-up” — meaning the roof has a more perplexing construction.
State of the Existing Roof
On the off chance that you want a complete roof replacement because your existing roof is vigorously damaged, then, at that point, this might influence the cost as well.
For instance, on the off chance that your roof has an opening in it that requires work on the hidden wood structure, this involves additional work and materials. Water might have seeped into your loft and upper floors, causing harm that needs to be repaired.
As a general rule, minor roof harm may not be that expensive, yet significant roof structural harm is probably going to be a lot costlier.